TL;DR: A telescopic hoist kit is specified from the cylinder's geometry, not from the trailer badge. Six measurements carry the whole job: collapsed length, stroke, stage count with each stage's outside diameter, mounting type and pin sizes, port position and thread, and the circuit. Get those right and a replacement drops straight in; get one wrong and the body jams half-way up or folds the smallest stage. The smallest stage is where the pressure peaks, so it is the stage that tells you whether the old kit was ever sized correctly.
A fleet operator sent me a hoist "for a 12-ton dump trailer" and nothing else. No measurements, no photo of the old ram, no idea whether it was front-mount or underbody. That one line tells you almost nothing. Two 12-ton trailers from different builders can want cylinders with different strokes, different collapsed lengths and different pin centres. I sent the driver a short measuring list, and the numbers he came back with changed the order entirely.
Why the trailer model is not a specification
The tipping geometry sets the cylinder, and the geometry belongs to the trailer builder, not to the tonnage. A front-mount hoist under the body needs a long stroke and a short collapsed length. The same body with an underbody cylinder closer to the hinge needs far less stroke but a much larger first-stage bore, because the moment arm is shorter and the force is higher.
That is the whole reason replacement kits are quoted from measurements. The nameplate gives you a starting point and a sanity check. The tape measure gives you the cylinder.
The six measurements that carry the order
Lower the body onto its mechanical prop before you touch anything. Never work under a body held up by hydraulics alone. Then take these six, in order.
- Collapsed length — pin centre to pin centre (or trunnion centre to top pin) with the cylinder fully closed.
- Stroke — measured on the old cylinder, or worked out from the tipping angle you need.
- Stage count and diameters — the number of moving stages and the outside diameter of each one.
- Mountings — eye or trunnion, pin diameters, eye widths, trunnion position.
- Oil port — position and thread type.
- Circuit — single- or double-acting, pump flow and relief setting.
A photo of the old ram next to a rule does more than any verbal description. If you still have the nameplate, send it too — the model reference lets us cross-check your figures against the builder's published geometry.
| Measurement | Why it matters | What goes wrong if skipped |
|---|---|---|
| Collapsed length | Sets the mounting envelope under the lowered body | Cylinder will not fit between the mounts |
| Stroke | Sets the dump angle at full extension | Body will not tip far enough to discharge |
| Stage count & diameters | Sets the force at each stage | Final stage stalls or folds at the top |
| Mountings & pins | Sets fit to the frame brackets | Pin centres off by millimetres block install |
| Port position & thread | Sets hose routing and sealing | Hose will not reach or leaks at the fitting |
| Circuit | Sets acting type and relief | Body creeps or the relief pops mid-lift |
Why the last stage takes the punishment
Each stage has its own effective area, and the largest stage extends first because it has the most area and so the most force at a given pressure. The load does not get lighter as the body rises — the moment arm improves a little, but the smallest stage still has to push a body that is now mostly vertical. Same force on a smaller area means higher pressure, and the final stage is where the pressure peaks.
That is why the last stage is the one that leaks, stalls or folds first. It is also why you ask for the stage diameter list, not just the first-stage bore. A kit quoted only from the base stage has not been checked at the stage that actually fails.
Front-mount or underbody: the kit changes shape
A front-mount hoist lifts the front of the body through a long, near-vertical stroke, so it is a slender, multi-stage unit with a short collapsed length — a 2.5:1 to 4:1 ratio of stroke to closed length is the packaging you are buying. An underbody cylinder sits further from the hinge, trades stroke for force, and runs a much bigger first stage with fewer stages overall.
Measure where the old cylinder sat before you assume the type. Two trailers that tip the same body can want kits that share almost no dimensions if one is front-mount and the other underbody.
What to ask for in the kit
Order the whole kit, not just the bare cylinder, and the install becomes a bolt-on job. The kit should carry the cylinder, the mounting pins and bushes, the hoses with swivels at the trunnion, a load-holding valve if the body stays raised in transit, and a breather for a single-acting circuit. Confirm the relief setting is below the ram's rating before the first lift — a relief set to the pump's pressure instead of the cylinder's is how a small final stage gets folded at full extension.
HCIC has built hydraulic cylinders and complete systems since 1998, from three plants and one R&D centre with 20+ engineers and 250+ staff. We produce 210,000 cylinders a year, 95% exported, to ISO 6020, ISO 6022 and ISO 10100. Every cylinder is pressure-tested before it ships — 3000 PSI proof on the lift range — with an 18-month warranty and a full maintenance kit included. MOQ is one sample, and a quote comes back within 48 hours.
For the compact DC motor-and-pump package that drives the hoist, see the hydraulic power units we pair with the kit. If the body itself creeps down in neutral, the load-holding note walks through the counterbalance checks.
Frequently asked questions
What do I measure to order a replacement telescopic hoist kit?
Six things: collapsed length pin-to-pin, full stroke, the number of stages and each stage's outside diameter, the mounting type and pin sizes, the port position and thread, and whether the circuit is single- or double-acting. A photo of the old cylinder or the nameplate helps confirm against your figures.
Why does the last stage of a telescopic cylinder carry the highest pressure?
The smallest stage has the smallest piston area, and the same load still needs the same force, so pressure peaks on the last stage. Force divided by the small area lands the final stage at or above the rest of the circuit, which is why that stage is the one that leaks or folds first.
Is a dump trailer telescopic hoist single- or double-acting?
Usually single-acting: oil extends the stages and the body's own weight pushes them back down. Double-acting telescopic hoists are used when the body must be powered back, such as on a push-out or ejector body with a horizontal cylinder.
Can you build a hoist kit to replace an existing brand-name cylinder?
Yes. HCIC builds telescopic hoist kits to the old cylinder's measurements or your drawing. Brand and model references are used for fitment only; no OEM authorization is claimed. Send the six measurements and we quote within 48 hours, with a one-sample MOQ.